Editor’s note: This is Part 2 of a three-part series on choosing and planting a tree.
Now that you’ve chosen the right tree for the location, you may think that planting it simply means digging a hole. But extensive research has been done on proper site preparation and planting methods to ensure that trees will thrive. First, the hole:
1. Make sure the soil is slightly moist. Never dig in soil that is very wet or very dry because it can degrade its structure, which means how soil granules clump or bind together. Good soil structure promotes water and air movement, optimizes biological activity and assists in root growth.
2. A shovel, spade or powered tiller can be used, but use caution when working with a tiller. Its overuse can degrade the soil structure and harm beneficial fungi, bacteria and earthworms that live in the soil.
3. The dimensions of the planting hole are determined by the size of the tree’s root ball. The width of the hole should be at least two times the width of the root ball. For example, a 12-inch diameter root ball requires a hole that is 24 inches or more in diameter. The depth of the hole must be no deeper than the depth of the root ball, measured from the root flare to the bottom of the root ball. The root flare is the area where the trunk widens and begins to form roots. To account for settling, you might make the hole not quite as deep as the root ball. In the example given, dig an 11-inch-deep hole for a 12-inch-deep root ball.
4. Set aside the soil that is removed from the hole. This is the native soil the tree will be growing in. After removing rocks, use it to backfill the planting hole.
5. When you are finished digging, examine the sides and surfaces of the hole. If they are smooth and shiny, roughen and scratch the sides. Smooth sides typically arise from high clay content. Roughening them allows tree roots to more easily penetrate the native soil that lies beyond.
The tree may be balled-and-burlapped, container-grown or bare-root. Each one has different requirements at planting time.
Planting a B&B tree:
1. Lift the tree by the root ball — never by the trunk — and place it in the center of the hole.
2. Rotate the tree to present its “best side” for viewing. Try to keep it in a vertical position.
3. Carefully remove burlap, wire, string or twine from the root ball and trunk. If the root ball is very heavy, it is OK to leave some burlap or wire underneath.
4. Lay a stick across the top of the planting hole. Confirm that the root flare is above the stick. If needed, pack additional soil into the bottom of the hole to raise the root ball.
5. Backfill with the native soil that was dug from the hole. Gently tamp it down around the root ball as you back-fill. Continue adding soil and tamping until the added soil is even with the surrounding soil. At this point, the root flare should be visible above soil level.
6. Add a 1- to 2-inch layer of mulch around the trunk to help with moisture retention, weed retardation and reduction of soil erosion. See note below on the dangers of excessive mulch.
7. Water the newly dug area and surrounding soil well. Best to use a soaker hose or allow water to slowly trickle from a garden hose over the planting area for several hours.
Planting a container-grown tree:
Follow steps 1 and 2 above.
3. Carefully remove the container, taking care to keep the root ball intact. Examine the root ball. If roots circle the outside of the root ball, they need to be cut so that they will begin to grow laterally after planting. This is best accomplished using a “box cut.” Cut the sides and bottom of the cylindrical root ball with a pruning saw so that it resembles a box. Now proceed with steps 4 through 7 above.
Planting bare-root trees, which are only available when dormant — early spring or late fall:
1. Examine the root system and prune out broken or damaged roots.
2. Dig a shallow hole that is 2 to 3 times wider than the root system spread.
3. Center the tree in hole, spread out the roots and add the native soil. Gently tamp the soil as the hole is filled until the added soil is even with the surrounding ground.
Continue with steps 4, 6 and 7 above.
Important details for planting any tree:
Feeder roots, which absorb and transport water and nutrients for the tree, are found in the top 12-18 inches of the soil. Making the planting hole as wide as possible gives these roots a good start. Breaking up the native soil is equally important. It helps to encourage lateral root growth and increases biological activity.
Do not add amendments such as compost or fertilizer to the planting hole. This stifles root growth by encouraging the roots to remain in the area where the living is easy. The goal is for the roots to quickly establish themselves in the native soil.
Finally and most importantly:
Do not pile mulch more than 2 inches deep on top of the root zone, covering the root flare. Overusing mulch can doom the tree. It increases moisture by the trunk and promotes disease and insect infestation. It encourages the growth of surface roots that can girdle the tree. Rodents can make their homes in deep mulch and feast on the bark of the tree. It also decreases the amount of oxygen reaching the roots, which is critical to a tree’s survival. These problems may not show up for months or years, at which point it may be too late to save the tree.
Steve Piskor is a Penn State master gardener and Pennsylvania certified horticulturist. Columns by master gardeners sometimes appear in place of the Garden Q&A by Sandy Feather, a Penn State Extension educator.





Comments
Welcome to Post-Gazette subscriber-only commenting community. Please review our community guidelines.